Searching 4 Obsolete 6.5 reamer

View previous topic View next topic Go down

Searching 4 Obsolete 6.5 reamer

Post by Toscano on Fri May 17, 2013 7:37 pm

I've got a little project in mind which I would like to start. The problem is finding an existing reamer. No, I'm not in a situatuation where I can afford to have a custom reamer produced. The cartridge is a 6.5 x 45 CZ. An obsolete (old timer) round which was developed as a wildcat. If anyone has any knowledge of or someone who would even rent it to me, I would truly appreciate it.
avatar
Toscano

Posts : 7
Join date : 2013-05-17
Age : 73
Location : Vista, CA

Back to top Go down

Re: Searching 4 Obsolete 6.5 reamer

Post by Rick459 on Wed May 22, 2013 12:42 am

toscano,
i have a 6.5 carcano finishing reamer that was made for me by PTG it's demesion's are 6.5x42. you need to find out wht the shoulder angle is as you might be able to use the 6.5 carcano reamer if the shoulder angle is the same just run it a little deeper. HTH.
Rick
avatar
Rick459
Member
Member

Posts : 147
Join date : 2011-04-30
Age : 69
Location : So.Cal

Back to top Go down

Re: Searching 4 Obsolete 6.5 reamer

Post by Toscano on Wed May 22, 2013 10:36 am

Rick,
Thanks for the info. The shoulder angle between the Carcano and the cartridge I had in mind are approximately similiar... the difference being 1.5 degrees. The Carcano being the lesser slope. In all probability, it should work. Let me know what you have in mind for its use. Thanks again.
avatar
Toscano

Posts : 7
Join date : 2013-05-17
Age : 73
Location : Vista, CA

Back to top Go down

The project is still on the board.

Post by Toscano on Tue Sep 17, 2013 3:05 am

Toscano wrote:I've got a little project in mind which I would like to start.  The problem is finding an existing reamer.  No, I'm not in a situatuation where I can afford to have a custom reamer produced.  The cartridge is a 6.5 x 45 CZ.  An obsolete (old timer) round which was developed as a wildcat.   If anyone has any knowledge of or someone who would even rent it to me, I would truly appreciate it.
Thank you
Reply with quote

Re: Searching 4 Obsolete 6.5 reamer

Post by Rick459 on Tue May 21, 2013 9:42 pm
+
toscano,
i have a 6.5 carcano finishing reamer that was made for me by PTG it's demesion's are 6.5x42. you need to find out wht the shoulder angle is as you might be able to use the 6.5 carcano reamer if the shoulder angle is the same just run it a little deeper. HTH.
Rick

Rick,
I lost track of this post when I went out of town...I ran across it by still searching for a reamer...If you still have that reamer I'd like to rent it or ??? Let me know what you might have in mind for my using it.
avatar
Toscano

Posts : 7
Join date : 2013-05-17
Age : 73
Location : Vista, CA

Back to top Go down

Re: Searching 4 Obsolete 6.5 reamer

Post by Toscano on Wed Jun 18, 2014 12:10 am

BTT
avatar
Toscano

Posts : 7
Join date : 2013-05-17
Age : 73
Location : Vista, CA

Back to top Go down

Re: Searching 4 Obsolete 6.5 reamer

Post by Toscano on Fri Jun 27, 2014 9:51 pm

BTT Rick, are you out there?
avatar
Toscano

Posts : 7
Join date : 2013-05-17
Age : 73
Location : Vista, CA

Back to top Go down

Re: Searching 4 Obsolete 6.5 reamer

Post by Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum